MX16FRO845-Bxx

 

NWAV™ X-Pol 16-Port Antenna
Download this datasheet

X-Pol 16-Port 8 ft, 45° Fast Roll-Off, with Smart Bias Ts, 698-3980 MHz:

4 ports 698-894 MHz, 8 ports 1695-2690 MHz, and 4 ports 3400-3980 MHz
  • 16-Port antenna offering the same functionality as 2 Hex Port antennas and CBRS in a single unit
  • Full low-band arrays for maximum gain
  • Fully integrated (iRETs) with independent RET control for low band and mid band
  • Optimized CBRS radiation patterns for improved RSRP and maximum EIRP
  • FET configured with internal RET for CBRS and ease of future network optimization
  • Excellent passive intermodulation (PIM) performance reduces harmful interference.
  • Suitable for 3G, 4G, and 5G interface technologies
  • Integrated Smart Bias-Ts reduce leasing costs and improved reliability
  • Optimized form factor for reduced wind loading

Fast Roll-Off antennas increase data throughput without compromising coverage
The horizontal beam produced by Fast Roll-Off (FRO) technology increases the Signal to Interference & Noise Ratio (SINR) by eliminating overlap between sectors .
Non-FRO antenna Large traditional antenna pattern overlap creates harmful interference. JMA FRO antenna
JMA’s FRO antenna pattern minimizes overlap, thereby minimizing interference.
LTE throughput SINR Speed (bps/Hz) Speed increase CQI
Excellent >18 >4.5 333+% 8-10
Good 15-18 3.3-4.5 277% 6-7
Fair 10-15 2-3.3 160% 4-6
Poor <10 <2 0% 1-3
The LTE radio automatically selects the best throughput based on measured SINR.
Electrical specification (minimum/maximum) Ports 1, 2, 3, 4 Ports 5, 6, 7, 8, 9, 10, 11, 12
Frequency bands, MHz 698-806 806-894 1695-1880 1850-1990 1920-2180 2300-2360 2496-2690
Polarization ± 45° ± 45°
Average gain over all tilts, dBi 15.7 16.3 18.0 18.7 19.5 20.4 19.2
Horizontal beamwidth (HBW), degrees1 48 45 44 42 36 32 30
Front-to-back ratio, co-polar power @180°± 30°, dB >25.0 >25.0 >25.0 >25.0 >25.0 >25.0 >25.0
X-Pol discrimination (CPR) at boresight, dB >25.0 >25.0 >18 >18 >18 >18 >18
Vertical beamwidth (VBW), degrees1 9 8 7.7 7.5 7.1 6.6 6.0
Electrical downtilt (EDT) range, degrees   2-12 2-12
First upper side lobe (USLS) suppression, dB1 ≤-15.0 ≤-15.0 ≤-16.0 ≤-16.0 ≤-16.0 ≤-16.0 ≤-16.0
Cross-polar isolation, port-to-port, dB1 25 25 25 25 25 25 25
Max VSWR / return loss, dB 1.5:1 / -14.0 1.5:1 / -14.0
Max passive intermodulation (PIM), 2x20W carrier, dBc -153 -153
Max input power per any port, watts 300 250
Total composite power all ports, watts 1500

1 Typical value over frequency and tilt

* For ports 13-16, the electrical downtilt is FET configured with internal RET, where the required electrical downtilt is defined at the time of order per the ordering information below.

Electrical specification (minimum/maximum)   Ports 13, 14, 15, 16
Frequency bands, MHz 3400-3550 3550-3700 3700-3980
Polarization   ± 45°
Average gain over all tilts, dBi 14.4 14.5 14.6
Horizontal beamwidth (HBW), degrees 37 36 36
Front-to-back ratio, co-polar power @180°± 30°, dB >25 >25 >25
Vertical beamwidth (VBW), degrees1 18.0 18.0 17.0
Electrical downtilt (EDT) range, degrees 2-12 orderable in 1 deg increments
First upper side lobe (USLS) suppression, dB1 ≤-15 ≤-15 ≤-15
Cross-polar isolation, port-to-port, dB1 25 25 25
Max VSWR / return loss, dB   1.5:1 / -14.0
Max input power per any port, watts 150
Total composite power all ports (1-10), watts 1500
Ordering information
Antenna model Description
MX16FRO845-Bxx (xx represents the FET in one degree increments for 3.4-3.98 GHz) 8F X- Pol 16 PORT FRO 45⁰ 2-12⁰/ 2-12⁰/2-12⁰, 4.3-10 & SBT
xx=02 thru 12 for each 1 degree tilt 3.4-3.98 GHz
Examples: MX16FRO865-B02 – 2deg, MX16FRO865-B09 – 9deg, MX16FRO865-B12-12deg
Optional accessories
AISG cables M/F cables for AISG connections
PCU-1000 RET controller Stand-alone controller for RET control and configurations
91900314-03 Dual Mount Bracket (see 91900314 bracket document for details)
Mechanical specifications
Dimensions height/width/depth, inches (mm) 96/ 20/ 8(2440/ 510/ 203)
Shipping dimensions length/width/height, inches (mm) 100.6/ 23.8/ 14.5(2555/ 605/ 368)
No. of RF input ports, connector type, and location 16 x 4.3-10 female, bottom
RF connector torque 96 lbf·in (10.85 N·m or 8 lbf·ft)
Net antenna weight, lb (kg) 90 (40.8)
Shipping weight, lb (kg) 137 (62.1)
Antenna mounting and downtilt kit included with antenna 91900318, 91900319 (middle bracket)
Net weight of the mounting and downtilt kit, lb (kg) 26 (11.82)
Range of mechanical up/down tilt -2° to 12°
Rated wind survival speed, mph (km/h) 150 (241)
Frontal and lateral wind loading @ 150 km/h, lbf (N) 172.3 (766.4), 79.8 (355.0)
EPA frontal and lateral, ft2, (m2) 7.7 (0.72), 3.6 (0.33)
Front view Back view Bottom view
Remote electrical tilt (RET 1000) information
RET location Integrated into antenna
RET interface connector type 8-pin AISG connector per IEC 60130-9 or RF port bias-t
RET connector torque Min 0.5 N·m to max 1.0 N·m (hand pressure & finger tight)
RET interface connector quantity 3 pairs of AISG male/female connectors and 3 RF port Bias Ts
RET interface connector location Bottom of the antenna
Total no. of internal RETs 698-894 MHz 1
Total no. of internal RETs 1695-2690 MHz 2
Total no. of internal RETs 3400-3980 MHz 1
RET input operating voltage, vdc 10-30
RET max power consumption, idle state, W ≤ 2.0
RET max power consumption, normal operating conditions, W ≤ 13.0
RET communication protocol AISG 2.0 / 3GPP
  RET and RF connector topology
 Each RET device can be controlled either via the designated external AISG connector or RF smart bias-t port as shown below: 
Band RF port
1695-2690 5-8
3400-3980 13-16
Band RF port
698-894 1-4
Band RF port
1695-2690 9-12
Note: The RET Device for 3400-3980 MHz is connected via the 1695-2690 Port 5 Bias T port or 1695-2690/3400-3980 MHz AISG ports.
Array topology

6 sets of radiating arrays

R1: 698-894 MHz

R2: 698-894 MHz

Y1: 1695-2690 MHz

Y2: 1695-2690 MHz

Y3: 1695-2690 MHz

Y4: 1695-2690 MHz

P1: 3400-3980 MHz

P2: 3400-3980 MHz
Band RF port
698-894 1-4
1695-2690 5-12
3400-3980 13-16

V2.0

12/12/23