MX04FFP665-01

 

NWAV™ X-Pol Four-Port Antenna
Download this datasheet

X-Pol Four-Port 6 ft, 65° Form in Tighter with Smart Bias Ts, 698-3980 MHz:

4 ports 698-3980 MHz

  • Low profile / smaller form-factor antennas suitable for shrouded sites, flagpoles, etc., for enabling full 4x4 C-Band spectrum deployment.

  • Integrated feeder reduction and Smart Bias-Ts for ease of deployment and reduced leasing costs

  • Optimized form-factor for reduced weight and wind loading

  • Fully integrated (iRETs) with independent RET control for low band, midband, and CBRS/C-Band.

  • Excellent passive intermodulation (PIM) performance reduces harmful interference.

  • Advanced element technology for improved RF efficiency

  • Optimized CBRS radiation pattern for improved RSRP

  • Consistent higher gain at 3.5 GHz with enhanced pattern characteristics

Electrical specification (minimum/maximum) Ports 1, 2 Ports 1, 2, 3, 4
Frequency bands, MHz 698-806 806-894 1695-1880 1850-1990 1920-2200
Polarization ± 45° ± 45°
Maximum gain over all tilts, dBi 14.4 14.5 17.6 17.8 18.1
Average gain over all tilts, dBi 14.0 ± 0.4 14.3 ± 0.2 17.3 ± 0.3 17.5 ± 0.3 17.7 ± 0.4
Horizontal beamwidth (HBW), degrees1 75.0 72.0 61.0 60.0 60.0
Front-to-back ratio, co-polar power @180°± 30°, dB >27 >26 >30 >31 >29
X-Pol discrimination (CPR) at boresight, dB >17.0 >15.6 >23 >18 >18
Vertical beamwidth (VBW), degrees1 13.0 12.0 6.0 5.5 5.4
Electrical downtilt (EDT) range, degrees   2-14 0-9
First upper side lobe (USLS) suppression, dB1 ≤-17.0 ≤-16.0 ≤-17.0 ≤-16.0 ≤-16.0
Cross-polar isolation, port-to-port, dB1 25 25 25 25 25
Max VSWR / return loss, dB 1.5:1 / -14.0 1.5:1 / -14.0
Max passive intermodulation (PIM), 2x20W carrier, dBc -153 -153
Max input power per any port, watts 300 200
Total composite power all ports (1-4), watts 1200

1 Typical value over frequency and tilt

Electrical specification (minimum/maximum)   Ports 1, 2, 3, 4
Frequency bands, MHz 3400-3550 3550-3700 3700-3980
Polarization   ± 45°
Maximum gain over all tilts, dBi 17.2 17.4 17.5
Average gain over all tilts, dBi 16.8 ± 0.4 17.1 ± 0.3 17.2 ± 0.3
Horizontal beamwidth (HBW), degrees 65 60 61
Front-to-back ratio, co-polar power @180°± 30°, dB >29 >30 >31
Vertical beamwidth (VBW), degrees1 8.4 8.1 7.9
Electrical downtilt (EDT) range, degrees 2-12
First upper side lobe (USLS) suppression, dB1 ≤-15 ≤-16 ≤-16
Cross-polar isolation, port-to-port, dB1 25 25 25
Max VSWR / return loss, dB   1.5:1 / -14.0
Max input power per any port, watts 150
Total composite power all ports (1-4), watts 1200

1 Typical value over frequency and tilt

 

Ordering information
Antenna model Description
MX04FFP665-01 6F X- Pol 4 Port FFP 65⁰ 2-14⁰/ 0-9⁰/ 2-12⁰, 4.3-10 & SBTs
Optional accessories
AISG cables M/F cables for AISG connections
PCU-1000 RET controller Stand-alone controller for RET control and configurations
91900339-01 (1 per 3 antennas) Tri-Sector Pole-Mount Bracket (see 91900339-01 bracket document for details)
Mechanical specifications
Dimensions height/width/depth, inches (mm) 72/ 12/ 6.5 (1828.8/ 304.8/ 165)
Shipping dimensions length/width/height, inches (mm) 76/ 20/ 14.5 (1930/ 508/ 368)
No. of RF input ports, connector type, and location 4 x 4.3-10 female, bottom
RF connector torque 96 lbf·in (10.85 N·m or 8 lbf·ft)
Net antenna weight, lb (kg) 42 (19.05)
Shipping weight, lb (kg) 55.3 (25.05)
Antenna mounting kit, 1 per 3 antennas (sold separately) See 91900339-01
Rated wind survival speed, mph (km/h) 150 (241)
Frontal and lateral, and rear wind loading @ 150 km/h, lbf (N) 62.6 (278.5), 14.5 (63.6)
EPA frontal and lateral, ft2, (m2) 2.8 (0.26), 0.7 (0.065)
Front view Back view Bottom view
Remote electrical tilt (RET 1000) information
RET location Integrated into antenna
RET interface connector type 8-pin AISG connector per IEC 60130-9 or RF port bias-t
RET connector torque Min 0.5 N·m to max 1.0 N·m (hand pressure & finger tight)
RET interface connector quantity 1 pair of AISG male/female connectors and 1 RF port bias-t
RET interface connector location Bottom of the antenna
Total no. of internal RETs 698-894 MHz 1
Total no. of internal RETs 1695-2200 MHz 1
Total no. of internal RETs 3400-3980 MHz 1
RET input operating voltage, vdc 10-30
RET max power consumption, idle state, W ≤ 2.0
RET max power consumption, normal operating conditions, W ≤ 13.0
RET communication protocol AISG 2.0 / 3GPP
RET and RF connector topology  
Each RET device can be controlled either via the designated external AISG connector or RF smart bias-t port as shown below: 

 

Band RF port Band RF port
3400-3980 1, 2, 3, 4 1695-2200 1, 2, 3, 4

 

Band RF port
698-894 1, 2
Array topology

5 sets of radiating arrays

R1: 698-894 MHz

B1: 1695-2200 MHz

B2: 1695-2200 MHz

P1: 3400-3980 MHz

P2: 3400-3980 MHz
Band RF port
698-894 1-2
1695-2200 1-2
1695-2200 3-4
3400-3980 1-2
3400-3980 3-4

V3.0

10/09/24