MX12FRO845-01

 

NWAV™ X-Pol 12-Port Antenna
Download this datasheet

X-Pol 12-Port 8 ft, 45° Fast Roll-Off, with Smart Bias Ts, 698-2690 MHz:

4 ports 698-894 MHz, 8 ports 1695-2690 MHz
  • 12-Port antenna offering the same functionality as 2 Hex Port antennas in a single unit
  • Full low-band arrays for maximum gain
  • Fully integrated (iRETs) with independent RET control for low band and mid band
  • Excellent passive intermodulation (PIM) performance reduces harmful interference.
  • Suitable for 3G, 4G, and 5G interface technologies
  • Integrated Smart Bias-Ts reduce leasing costs and improved reliability
  • Optimized form factor for reduced wind loading

Fast Roll-Off antennas increase data throughput without compromising coverage
The horizontal beam produced by Fast Roll-Off (FRO) technology increases the Signal to Interference & Noise Ratio (SINR) by eliminating overlap between sectors .
Non-FRO antenna Large traditional antenna pattern overlap creates harmful interference. JMA FRO antenna
JMA’s FRO antenna pattern minimizes overlap, thereby minimizing interference.
LTE throughput SINR Speed (bps/Hz) Speed increase CQI
Excellent >18 >4.5 333+% 8-10
Good 15-18 3.3-4.5 277% 6-7
Fair 10-15 2-3.3 160% 4-6
Poor <10 <2 0% 1-3
The LTE radio automatically selects the best throughput based on measured SINR.
Electrical specification (minimum/maximum) Ports 1, 2, 3, 4 Ports 5, 6, 7, 8, 9, 10, 11, 12
Frequency bands, MHz 698-806 806-894 1695-1880 1850-1990 1920-2180 2300-2360 2496-2690
Polarization ± 45° ± 45°
Average gain over all tilts, dBi 15.7 16.3 18.0 18.7 19.5 20.4 30.0
Horizontal beamwidth (HBW), degrees1 46 44 44 42 36 32 31
Front-to-back ratio, co-polar power @180°± 30°, dB >25.0 >25.0 >25.0 >25.0 >25.0 >25.0 >25.0
X-Pol discrimination (CPR) at boresight, dB >25.0 >25.0 >18 >18 >18 >18 >18
Vertical beamwidth (VBW), degrees1 9 8 7.7 8.0 7.1 6.5 6.2
Electrical downtilt (EDT) range, degrees   2-12 2-12
First upper side lobe (USLS) suppression, dB1 ≤-15.0 ≤-15.0 ≤-16.0 ≤-16.0 ≤-16.0 ≤-16.0 ≤-16.0
Cross-polar isolation, port-to-port, dB1 25 25 25 25 25 25 25
Max VSWR / return loss, dB 1.5:1 / -14.0 1.5:1 / -14.0
Max passive intermodulation (PIM), 2x20W carrier, dBc -153 -153
Max input power per any port, watts 300 250
Total composite power all ports, watts 1500

1 Typical value over frequency and tilt

Mechanical specifications
Dimensions height/width/depth, inches (mm) 96/ 20/ 8(2440/ 510/ 203)
Shipping dimensions length/width/height, inches (mm) 100.6/ 23.8/ 14.5(2555/ 605/ 368)
No. of RF input ports, connector type, and location 12 x 4.3-10 female, bottom
RF connector torque 96 lbf·in (10.85 N·m or 8 lbf·ft)
Net antenna weight, lb (kg) 85 (38.5)
Shipping weight, lb (kg) 130 (58.9)
Antenna mounting and downtilt kit included with antenna 91900318, 91900319 (middle bracket)
Net weight of the mounting and downtilt kit, lb (kg) 26 (11.82)
Range of mechanical up/down tilt -2° to 12°
Rated wind survival speed, mph (km/h) 150 (241)
Frontal and lateral wind loading @ 150 km/h, lbf (N) 172.3 (766.4), 79.8 (355.0)
EPA frontal and lateral, ft2, (m2) 7.7 (0.72), 3.6 (0.33)
Front view Back view Bottom view
Ordering information
Antenna model Description
MX12FRO845-01 8F X- Pol 12 PORT FRO 45⁰ 2-12⁰/ 2-12⁰ RET, 4.3-10 & SBT
Optional accessories
AISG cables M/F cables for AISG connections
PCU-1000 RET controller Stand-alone controller for RET control and configurations
91900314-03 Dual Mount Bracket (see 91900314 bracket document for details)
Remote electrical tilt (RET 1000) information
RET location Integrated into antenna
RET interface connector type 8-pin AISG connector per IEC 60130-9 or RF port bias-t
RET connector torque Min 0.5 N·m to max 1.0 N·m (hand pressure & finger tight)
RET interface connector quantity 3 pairs of AISG male/female connectors and 3 RF port Bias Ts
RET interface connector location Bottom of the antenna
Total no. of internal RETs 698-894 MHz 1
Total no. of internal RETs 1695-2690 MHz 2
RET input operating voltage, vdc 10-30
RET max power consumption, idle state, W ≤ 2.0
RET max power consumption, normal operating conditions, W ≤ 13.0
RET communication protocol AISG 2.0 / 3GPP
    RET and RF connector topology
   Each RET device can be controlled either via the designated external AISG connector or RF smart bias-t port as shown below: 
Band RF port
1695-2690 5-8
Band RF port
698-894 1-4
Band RF port
1695-2690 9-12
 
Array topology

6 sets of radiating arrays

R1: 698-894 MHz

R2: 698-894 MHz

Y1: 1695-2690 MHz

Y2: 1695-2690 MHz

Y3: 1695-2690 MHz

Y4: 1695-2690 MHz
Band RF port
1695-2690 5-12
698-894 1-4

V2.0

12/11/23