MX04FIT345-01

  

NWAV™ X-Pol Panel Antenna

Download this datasheet

4-Port 30 in. FIT (Form in Tighter), 3550 - 3700 MHz
  • X-Pol, small cell, panel antenna

  • Suitable for pole or building mount

  • 4x4 MIMO for CBRS

  • Integrated (internal RET) for remote electrical tilt control

 

 

Electrical specification (minimum/maximum) Ports 1, 2, 3, 4
Frequency bands, MHz 3550-3700
Polarization ± 45°
Average gain over all tilts, dBi 19.0
Horizontal beamwidth (HBW), degrees 45.0
Front-to-back ratio, co-polar power @180°± 30°, dB 25
X-Pol discrimination (CPR) at boresight, dB >18
Vertical beamwidth (VBW), degrees1 7.3
Remote electrical downtilt (EDT) range, degrees 0-10
First upper side lobe (USLS) suppression, dB1 17
Cross-polar isolation, port-to-port, dB1 25
Max VSWR / return loss, dB 1.5:1 / -14.0
Max passive intermodulation (PIM), 2x20W carrier, dBc -140
Max input power per any port, watts 100

1 Typical value over frequency and tilt

Mechanical specifications
Dimensions height/width/depth, inches (mm) 32.67/ 11.6/ 4.53 (830/ 295/ 115)
Shipping dimensions length/width/height, inches (mm) 37.4/ 16.9/ 11.8 (950/ 430/ 300)
No. of RF input ports, connector type, and location 4 x 4.3-10 female, bottom
RF connector torque 96 lbf·in (10.85 N·m or 8 lbf·ft)
Net antenna weight, lb (kg) 16.0 (7.3)
Weight with supplied pipe mount bracket, lb (kg) 48.6 (22.0)
Shipping weight, lb (kg) 45.2 (20.5)
Rated wind survival speed, mph (km/h) 150 (241)
Frontal wind loading @ 150 km/h, lbf (N) 56.9
Front view Back view Bottom view
Ordering information
Antenna model Description
MX04FIT345-01 30 inch panel antenna, 4 ports CBRS with RET
Mounting kit (included) 91900318 BRACKET KIT, range of mechanical up/down tilt -2° to 12°
Optional accessories
AISG cables M/F cables for AISG connections
PCU-1000 RET controller Stand-alone controller for RET control and configurations
Remote electrical tilt (RET 1000) information
RET location Integrated into antenna
RET interface connector type 8-pin AISG connector per IEC 60130-9
RET connector torque Min 0.5 N·m to max 1.0 N·m (hand pressure & finger tight)
RET interface connector quantity 1 pair of AISG male/female connectors
RET interface connector location Bottom of the antenna
Total no. of internal RETs 1
RET input operating voltage, vdc 10-30
RET max power consumption, idle state, W ≤ 2.0
RET max power consumption, normal operating conditions, W ≤ 13.0
RET communication protocol AISG 2.0 / 3GPP
RET and RF connector topology
Each RET device can be controlled either via the designated external AISG connector or RF port as shown below: 

 

RET device Band RF port
1 3550-3700 1-4
Array topology

2 sets of radiating arrays

P1: 3550-3700 MHz

P2: 3550-3700 MHz
Band RF port
3550-3700 1-4

V2.0

12/12/23